1、 Shape and size of specimen aerated concrete

自上料攪拌車，測定混凝土立方體試件抗壓強度，也可以按粗骨料大粒徑的尺寸而選用不同試件的尺寸。但是試件尺寸不同、形狀不同，會影響試件的抗壓強度測定結果。因為混凝土試件在壓力機上受壓時，在沿加荷方向發[本文先發在礦山機械/=百///科/=網]生縱向變形的同時，也按泊松比效應產生橫向膨脹。而鋼制壓板的橫向膨脹較混凝土小，因而在壓板與混凝土試件受壓面形成磨擦力，對試件的橫向膨脹起著約束作用，這種約束作用稱為"環箍效應"。

From the loading mixer, the compressive strength of concrete cube specimens can be measured, and different specimen sizes can also be selected according to the large particle size of coarse aggregate. However, different specimen sizes and shapes will affect the determination results of compressive strength. Because when the concrete specimen is pressed on the press, while the longitudinal deformation occurs along the loading direction [this paper first occurs in mining machinery / = Bai / / Ke / = net], the transverse expansion also occurs according to the Poisson's ratio effect. The transverse expansion of the steel plate is smaller than that of the concrete, so the friction force is formed on the compression surface of the plate and the concrete specimen, which restricts the transverse expansion of the specimen, which is called "hoop effect".

"環箍效應"對混凝土抗壓強度有提高作用。自上料攪拌車，離壓板越遠，"環箍效應"小，在距離試件受壓面約0.866α（α為試件邊長）范圍外這種效應消失。

"Hoop effect" can improve the compressive strength of concrete. From the loading mixer, the farther away from the pressing plate, the "hoop effect" is small, about 0.866 from the compression surface of the test piece α （ α This effect disappears outside the range of specimen side length).

混凝土受壓破壞在進行強度試驗時，試件尺寸越大，測得的強度值越低。

In the strength test of concrete compression failure, the larger the specimen size is, the lower the measured strength value is.

原因分析：

Cause analysis:

1、"環箍效應"；

1. "Hoop effect";

2、由于大試件內存在的孔隙、裂縫和局部較差等缺陷的機率大，從而降低了材料的強度。標準GBJ107-87《混凝土強度檢驗評定標準》規定邊長為150mm的立方體試件為標準試件。自上料攪拌車，當采用非標準尺寸試件時，應將其抗壓強度折算為標準試件抗壓強度。折算系數需按以下的規定。

2. Due to the high probability of pores, cracks and local defects in large specimens, the strength of the material is reduced. The national standard GBJ107-87 standard for inspection and evaluation of concrete strength stipulates that the cube specimen with side length of 150mm is the standard specimen. When non-standard size specimens are used for self loading mixer, their compressive strength shall be converted into the compressive strength of standard specimens. The conversion coefficient shall be in accordance with the following provisions.

3、混凝土抗壓強度試塊允許小尺寸表骨料大顆粒直徑（mm）換算系數試塊尺寸（mm）31.50.95100×100×100（非標準試塊）401.00150×150×150（標準試塊）601.05200×200×200（非標準試塊）

3. Allowable small size of concrete compressive strength test block table aggregate large particle diameter (mm) conversion coefficient test block size (mm) 31.50.95100 × one hundred × 100 (non-standard test block) 401.00150 × one hundred and fifty × 150 (standard test block) 601.05200 × two hundred × 200 (non-standard test block)

二、表面狀態加氣混凝土

2、 Surface condition aerated concrete

自上料攪拌車，當混凝土受壓面非常光滑時（如有油脂），由于壓板與試件表面的磨擦力減小，使環箍效應減小，試件將出現垂直裂紋而破壞，測得的混凝土強度值較低。

From the loading mixer, when the concrete compression surface is very smooth (if there is grease), the hoop effect will be reduced due to the reduction of the friction force between the pressing plate and the surface of the specimen, the specimen will be damaged by vertical cracks, and the measured concrete strength value is low.

三、含水程度混凝土試件含水率越高，其強度越低。

3、 The higher the moisture content of concrete specimen, the lower its strength.

四、加荷速度

4、 Loading speed

自上料攪拌車，在進行加氣混凝土試件抗壓試驗時，加荷速度過快，材料裂紋擴展的速度慢于荷載增加速度，故測得的強度值偏高。在進行混凝土立方體抗壓強度試驗時，應按規定的加荷速度進行。綜上所述，通過對混凝土強度影響因素的分析，提高混凝土強度的措施有：采用強度等級高的水泥；采用低水灰比；采用有害雜質少、級配良好、顆粒適當?shù)墓橇虾秃侠淼纳奥剩徊捎煤侠淼臋C械攪拌、振搗工藝；保持合理的養護溫度和一定的濕度，可能的情況下采用濕熱養護；摻入合適的混凝土外加劑和摻合料。

During the compression test of aerated concrete specimen by self loading mixer, the loading speed is too fast, and the crack propagation speed of material is slower than the load increase speed, so the measured strength value is high. During the concrete cube compressive strength test, it shall be carried out according to the specified loading speed. To sum up, through the analysis of the influencing factors of concrete strength, the measures to improve concrete strength include: using cement with high strength grade; Adopt low water cement ratio; Adopt aggregates with less harmful impurities, good grading, appropriate particles and reasonable sand ratio; Adopt reasonable mechanical mixing and vibration technology; Maintain reasonable curing temperature and certain humidity, and adopt damp heat curing when possible; Add appropriate concrete admixtures and admixtures.